Dropped connections, slow speeds, or the inability to connect new devices can all point to the need for a reset. A factory reset can often clear out any glitches or incorrect configurations, providing a clean slate for optimal performance. Let's dive into how you can easily reset your RangeXTD and reclaim your seamless WiFi experience.
RangeXTD WiFi Extender Reset Processes:
There are two types of reset in your RangeXTD booster: one is soft reset and second is hard reset. Both the reset processes are defined right below.
Soft Reset
To perform a soft reset is to unplug the power adapter of your WiFi repeater from the wall outlet or the device itself. Wait for about 10 seconds, and then plug it back in. Allow a few minutes for the repeater to power on and reconnect.
You can also do this same thing by pressing the Power button twice on the repeater. The first press will the turn the extender off and one more press will turn the extender on.
Hard Factory Reset
Hard resetting the device will restores your WiFi extender to its original factory default settings. This means all your custom configurations, including the extended network name (SSID), password, and any other settings you've changed, will be erased. You'll need to set it up again from the beginning. We have added a list of when to should reset the device.
Forgotten the login password for the repeater's configuration page.
Experiencing persistent issues with the repeater that a simple reboot doesn't fix.
Giving the repeater away or selling it and want to clear your personal settings.
Want to start the configuration process over.
Now, let’s have look how to reset the device:
You will find the reset button on side of the device. You'll need a paperclip to press it.
Ensure the extender is plugged in and powered on. Using your paperclip or pin, gently press and hold the reset button. You should feel a slight click.
Keep the button pressed for approximately 10 seconds. Holding it for too short a time might just reboot the device instead of performing a full factory reset.
After the specified time, release the button. The extender should now begin the reset process. You'll likely see the indicator lights blink or behave in a specific pattern indicating the reset is underway. Give the extender a few minutes to fully reboot and return to its factory default settings. The lights should eventually stabilize.
Now, you have to reconfigure the device with the help of the step-by-step information given down here:
Re-Configuration
Via WPS
Place your RangeXTD booster in an outlet roughly halfway between your router and the area where you want to extend the WiFi signal.
Ensure the mode switch on the side or back of your RangeXTD is set to "Repeater" or "Extender" mode.
Press the WPS button on your RangeXTD booster.
Within 2 minutes of pressing the WPS button on the RangeXTD, press the WPS button on your router.
The lights on both the RangeXTD and the Orbi router should blink, indicating they are trying to connect.
Via Web Interface
Open the WiFi settings on your computer and look for the default WiFi network name of the RangeXTD.
Once connected to the RangeXTD's network, open a web browser.
Type the default IP address 192.168.7.234 of the RangeXTD. Press Enter.
Enter RangeXTD login username and password. The default username and password are often both "admin".
Once logged in, you should see a setup wizard or a menu with different modes. Select "Repeater" or "Extender" mode.
The RangeXTD should scan for nearby WiFi networks. Select your Orbi's WiFi network name (SSID) from the list.
Enter the password for your Orbi's WiFi network.
Enter it carefully. Some extenders allow you to set a new name (SSID) for the extended network.
Click Apply, to save your settings. The RangeXTD will likely reboot.
The Conclusion
The factory reset is a powerful tool in your RangeXTD troubleshooting arsenal. When other solutions fall short, bringing your extender back to its original state can often resolve persistent connection problems and allow you to start the setup process anew.
